Thermaltake Pacific CLM360 Ultra Hard Tube Liquid Cooling Kit (CL-W335-CU12SW-A)
In stock at Umart
Price checked today
We may earn a commission if you buy; it doesn't change your price. Check the price at Umart before you buy. How we make money
Price history
Tracking since today
The price hasn't changed since we started tracking it. We'll show its history once it does.
About this product
- Brand
- Thermaltake
- Store
- Umart
- Category
- Electronics > Electronics Accessories > Computer Components > Computer System Cooling Parts > All-in-One Liquid CPU Coolers
- SKU
- 68022
SPECIFICATIONS:
| Dimension(s) | 520 (L) x 200 (W) x 232 (H) |
| Compatibility | Intel LGA 1700/1366/1156/1155/1151/1150 AMD AM5/AM4/AM3+/AM3/AM2+/AM2/FM2/FM1 |
| Components dimension | Pump & Reservoir: 74.8 (L) x 74.8 (W) x 267 (H) Copper Radiator : 406 (L) x 119 (W) x 40 (H) |
| Tube dimension | OD : 16mm , ID : 12mm |
| Fan spec | PWM 500 With L.N.C PWM 500 |
| Coolant | T1000 Coolant Pure Clear |
| Kit contents | CPU Water Block - Pacific MX2 Ultra CPU Water Block x1 Pump/Reservoir - Pacific PR32-D5 Plus Pump/Reservoir Combo x1 Copper Radiator - Pacific CLM360 Radiator 40 (H) x 119 (W) x 406 (L) mm x1 Fan -Riing Duo 12 RGB Radiator Fan x3 Fittings - Pacific C-Pro G14 PETG 16mm OD Compression - Black x8 - Pacific G1/4 90 Degree Adapter - Black x2 - Pacific G14 Male to Male 10mm extender – Black x1 Coolant - Thermaltake T1000 Coolant Pure Clear x1 Tube - V-Tubler PETG Tube 16mm OD 500mm x 8 Accessory - Intel and AMD Universal Back plate & Mounting Kit - 24pin ATX Bridge Tool x1 - Thermaltake Thermal Grease x1 - Silicone insert x1 |
Cautions:
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
Fill the reservoir to the top as it will prevent air from going into the pump
If necessary tilt the system slightly from side to side to bleed the air out of the loop.
Place some paper towels under fittings and joining points to test for leaks.
Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
Coolant might fade over time.